![]() In some parts of Missouri and across the Midwest, drought conditions are starting to appear and could last for an extended period of time. Many seed suppliers are running short or have run out of sorgum sudan and pearl millet seed because producers used large parts of their hay reserve from last year and hay crops this year have been about 50%. This sends people looking for an alternative forage crop for livestock. ( via NIDIS, 10 June 2018. Pictured above) We’ve had producers calling us over the past few weeks inquiring about baling and wrapping corn silage, and the process of it. So we are going to break it down into tangible steps you can take to help yourself regarding drought damaged corn. How does a drought affect corn? Drought affects corn when the nitrates used to make the plant grow remain at the bottom of the stalk, which puts drought stressed corn at a higher risk for nitrate levels being high. “High nitrate levels are frequently found where high levels of nitrogen fertilizer were applied and where drought-damaged corn is chopped a few days after a rain. Other factors that contribute to high nitrate levels in corn silage are cloudy weather, extremely high plant populations and shortages of soil phosphorus and potassium." (Kallenbach, 2012.) What can be done? 1. ChopAccording to the University of Missouri Ag Extension, if corn has been damaged from drought, you should chop it to help with compression of plant material. This “should help in packing the silage to exclude as much oxygen as possible. Producers should also sharpen the knives on their equipment before making silage.” (Kallenback, 2012). Chopping will make the next two points easier as well. Like mentioned above, by chopping-the bale you make will be tighter- which will have less oxygen and will make ensiling faster. It will also make mixing easier, since the bale will process better since it is already chopped and won’t have to be chopped again in the TMR mixer. 2. Ensile"Ensiling drought-damaged corn is preferred to greenchop because during the fermentation process, the nitrate content can be reduced by 20 to 50 percent.” (Kallenbach, 2012.) How to ensile? “Simply bale high moisture forage and then wrap the bales with plastic film to exclude oxygen.” (Kallenbach, 2012) It is recommended to apply 6-8 layers of plastic wrap. How has it worked for others? The University of Missouri mentions a test plot of corn silage in their article called “During Drought, consider baling corn silage.” “In 2016, a Lawrence county dairyman baled a test plot of corn for silage in collaboration with University of Missouri - Extension, S&H Farm Supply, and Crown Power of Monett. Two balers used included newly available crop cutting technology, while the third baler was a standard baler. Corn was mowed with a roller mower. This method helped keep cobs intact on plants and not left in the field. This type of mower also allowed the corn to fall in rows to accommodate the baler without tedding or raking. Corn wilted in the field until it reached 75% moisture. Corn was baled, net wrapped then wrapped in white plastic. These bales then underwent fermentation until early October. ‘The fermentation profile was remarkably similar to typical corn silage,’ Said Bluel. At feedout, cows wasted little feed and milked well. The project demonstrated that baled corn is a viable feed solution.” (Bluel, 2018). 3. MixEven though letting the corn ensile will reduce nitrates by 20-50%, if it still tests at a risky level, your other option is to mix it with other stuffs in a TMR mixer. The University of Nebraska-Lincoln agrees that “add(ing) whole corn, dried distillers grains, or ground dry forage” will give you a better chance of feeding a high quality, lower nitrate ration with your corn silage. (Rasby, Anderson). The University of Missouri also recommends diluting “the silage in the ratio with other low nitrate feedstuffs.” (Kallenbach, 2012.) Feeding from a TMR mixer in general is a practice that allows you to manage exactly what your livestock is getting per serving, because its mixed in a homogenous mix that doesn’t allow them to pick through it, and it creates less waste. For more information, see the articles listen in our references: Bluel, Reagan. University of Missouri Extension. “During Drought, consider baling corn silage.” 6 July 2018. http://extension.missouri.edu/barry/documents/Baled%20Corn%20Silage.pdf Kallenbach, Rob. University of Missouri. “Making silage from drought damaged corn.” 20 July 2012. https://ipm.missouri.edu/IPCM/2012/7/Making-Silage-from-Drought-Damaged-Corn/ NIDIS. National Integrated Drought Information System. U.S. Drought Portal. 10 June 2018. https://www.drought.gov/drought/regions Rasby, Rick and Bruce Anderson. Nebraska Institute of Agriculture and Natural Resources. “Options for Drought Damaged Corn Fields.” 10 June, 2018. https://beef.unl.edu/cattleproduction/droughtdamagedcornfields Roth, Greg and Doug Beegle. Penn State College of Agricultural Sciences. “High Nitrate Potential in Corn Silage” 10 June 2018. https://agsci.psu.edu/aasl/plant-analysis/at-harvest-corn-silage-nitrate-test/high-nitrate-potential-in-corn-silage University of Illinois Extension. “Drought Stressed Corn as Livestock Feed: Frequently Asked Questions.” 6 August 2012. http://www.beefmagazine.com/disaster/drought-stressed-corn-livestock-feed-frequently-asked-questions Wheaton, Howell and Fred Martz. University of Missouri Ag Extention. “Corn Silage” 10 June, 2018. https://extension2.missouri.edu/g4590 Comments are closed.
|